The Airaid PowerAid Custom Throttle Body Spacer # AR450-638 that you referenced should work just fine with the cold air intake system you have installed on your 2011 Ford Mustang. It will add about an inch to your intake track length which your cold air kit shouldn't have a problem accommodating.
Running two throttle body spacers would be a bit redundant and would greatly increase the chance of experiencing a fit issue so I can't recommend you go that route. view full answer...
We do carry a throttle body spacer to fit your F-350 with the 7.3L. It's part # AR400-521 from Airaid.
I've linked the install details for you as well. view full answer...
When installing the Airaid PowerAid Custom Throttle Body Spacer # AR200-540 you may need to extend the lines to reach the extended spot on the TBI, do so. Some cruise or kickdown cables may require adjustment. view full answer...
The Airaid PowerAid Custom Throttle Body Spacer, part # AR200-630-1, which you references, fits both the 2015 Chevy Camaro with 3.6L V6 and 6.2L V8 engines. The blades of this throttle body booster cause air entering the engine to tumble and spin. This ensures a highly atomized fuel-air mixture in the combustion chamber, which boosts fuel efficiency.
I have included the installation instructions for part # AR200-630-1 for you to check out. view full answer...
The Airaid PowerAid Custom Throttle Body Spacer # AR300-631-1 is a fit for your 2018 Ram 2500 with the 6.4L HEMI. I checked with the manufacturer to confirm the fit and it will work well for your truck. I've attached the installation instructions to assist. view full answer...
The Airaid PowerAid Custom Throttle Body Spacer, part # AR510-621, is a compatible fit for your 4.6 liter 2011 Toyota Tundra. It is legal in all 50 states and compliant with the California Air Resources Board, is made in the USA, and comes with a limited lifetime warranty. view full answer...
If you have a 3.6L engine in your 2015 Colorado, the Airaid PowerAid Custom Throttle Body Spacer, part # AR200-630-1 is confirmed as a fit for your truck. This comes with the gaskets and hardware included.
This spacer helps improve horsepower and engine torque while improving fuel efficiency. view full answer...
As long as your 2011 Dodge Ram 1500 with 4.7 liter engine is equipped with the factory throttle body and intake system, the Airaid PowerAid Custom Throttle Body Spacer, # AR300-626, will work for you. The helix bore design causes incoming air to tumble and spin. This highly atomized fuel-air mixture - along with an elongated intake tract that increases air velocity - leads to more power.
Another great way to increase your engine's performance is to use a programmer like the Edge Evolution... view full answer...
Since spacers are brand specific, you would need to know what brand of air bags that you have so that you can install the proper spacers. From the picture that you sent, unfortunately there is no way to be able to identify the brand of air bags that you have. I reached out to Firestone to see if they could identify the air bags and they said that even though they couldn't identify them from the picture, you could use their spacers as long as the hole configurations are the same and the... view full answer...
First of all if the truck has a body lift and not a suspension lift then you will not need spacers at all.
If you do have a suspension lift on your 2012 Ford F-250 then to install the Firestone Ride-Rite # F2597 you need to choose the Lift Spacers that equal the amount of lift you have, or as close as possible. I've linked our selection for you. view full answer...
The air bag helper springs available for the 2007 Jeep Grand Cherokee do not have spacers that will work with them but you can use Timbren springs # TJRC04 by using some spacers, # A25723-90AH00. This is a single 1 inch spacer so you would have to use 4 of them total since you have a 2 inch lift.
The use of spacers would only be needed if the lift on your Jeep makes the frame further from the axle (suspension lift). If it has just made the body higher up from the frame then spacers would... view full answer...
Since your 2008 Ford F-350 has a 4 inch lift you will need spacers # F2370 to install Firestone air bags # F2550. This is assuming you have a suspension lift that moves the truck frame further away from the axle. If you have a body lift then you will not need the spacers. view full answer...
The Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle # F2609 does NOT require the Lift Spacers for Firestone Ride-Rite Air Helper Springs - 2" Spacers - Qty 2 # F2366 for your truck.
You may want consider adding a compressor to this kit. I recommend the Air Lift WirelessONE Compressor System # AL25980 which will allow you to adjust the pressure at any time from the comfort of your cab or outside the cab if preferred. view full answer...
Air Lift LoadLifter 7500 XL Air Helper Springs # AL57538 can be installed in your 2019 Chevrolet Silverado 3500 even if it has a suspension lift. If the truck actually has a 6-inch lift you're going to need spacer kit # F2374. The upper and lower air bag brackets once installed should be between 8-1/2 and 9-1/2-inches apart. Trucks with a body lift do not need spacers. view full answer...
I spoke to my representative at Magnaflow and they stated that you can typically expect an increase in horsepower and torque up to 8HP and 10TQ respectively with the MagnaFlow Exhaust System part # MF15580 installed on your 2012 Nissan Frontier. The choking upon accelerating will not be caused by the Volant Cold Air Intake nor fixed by installing the Magnaflow exhaust system. This is likely an issue with your throttle body or catalytic converter.
A cold air intake paired with an exhaust... view full answer...
A truck with a body lift, as opposed to a suspension lift, can use a rear-axle jounce spring kit like the Timbren # TDDR00 without any additional parts or special installation procedures. This kit is a valid fit for your 2001 Dodge Dakota. The written install instructions are linked for your reference.
A truck with a suspension lift would require additional spacers such as # A25723-90AH00. view full answer...
The SumoSprings Solo Custom Helper Springs # SS98DR, which fit a 2014 - 2021 Nissan Frontier, will fit as long as the lift is a body lift and it doesn't actually lift the frame of your vehicle.
If it does lift the frame then I recommend picking up the Timbren Active Off-Road Bumpstops # TABSOSR which will be a bit more rigid but you'll be able to add spacers like the 1" Spacer # A25723-90AH00 to help take up that extra space. You'll just have to measure the available space and choose... view full answer...
It depends on how your 2006 Dodge Ram 2500 4x4 was lifted. If it was a body lift then you would not need spacers. But on suspension lifts, which is what I believe you have, you would need spacers equal to the amount of the actual lift. So if the distance from the factory bump stop to the axle has increased 2 inches you would need 2 inches of spacers to install # TDF25004B.
The 1 inch Timbren spacers are # A25723-90AH00 and you would need 2 on each side if you do need 2 inches. Longer hardware... view full answer...
Typically block lifts are body lifts which do not add distance between the axle and the frame. If that's what you have then the Firestone Ride Rite kit part # F2709 would fit as-is. If you do have a lift that adds distance between the axle and the frame you'd need a spacer kit like the part # F2536 which is a 1-1/4 inch spacer block. view full answer...
The Air Lift AirLift 1000HD Air Helper Springs for Coil Springs - Rear # AL60818HD is a great product for your 2017 Ram 1500 but it doesn't account for the lift. The Timbren Rear Suspension Enhancement System # TDRTT1500 will work for your truck but you will need to use spacers to account for your lift if it is a suspension lift and not a body lift. The Timbren 1" Spacer For Raised Frame Vehicles - 1/2" bushing # TA25723-90AD00 and the Timbren 1/2" Spacer For Raised Frame Vehicles - 1/2"... view full answer...
Go To Results